This paper proposes a reconfigurable adaptive FEC system based on Reed-Solomon (RS) code with interleaving. In adaptive FEC schemes, error correction capability t is changed dynamically according to the communication channel condition. For given error correction capability t, we can implement an optimal RS decoder composed of minimum hardware units for each t. If the hardware units of the RS decoder can be reduced for any given error correction capability t, we can embed as large deinterleaver as possible into the RS decoder for each t. Reconfiguring the RS decoder embedded with the expanded deinterleaver dynamically for each error correction capability t allows us to decode larger interleaved codes which are more robust error correction codes to burst errors. In a reliable transport protocol, experimental results show that our system achieves up to 65% lower packet error rate and 5.9% higher data transmission throughput compared to the adaptive FEC scheme on a conventional fixed hardware system. In an unreliable transport protocol, our system achieves up to 76% better bit error performance with higher code rate compared to the adaptive FEC scheme on a conventional fixed hardware system.

Fractional Motion Estimation (FME) is an advanced feature adopted in H.264/AVC video compression standard with quarter-pixel accuracy. Although FME could gain considerably higher encoding efficiency, sub-pixel interpolation and sum of absolute transformed difference (SATD) computation, as main parts of FME, increase the computation complexity a lot. To reduce the complexity of FME, this paper proposes a full computation reusable VLSI oriented algorithm. Through exploiting the similarity among motion vectors (MVs) of partitions in the same macroblock (MB), temporary computation results can be fully reused. Furthermore, a simple and effective searching method is adopted to make the proposed method more suitable for VLSI implementation. Experiment results show that up to 80% add operations and 85% internal reference frame memory access operations are saved without any degradation in the coding quality.

Power efficiency and real-time processing capability are two major issues in today's mobile video applications. We proposed a novel Motion Estimation (ME) engine for power-efficient real-time MPEG-4 video coding based on our previously proposed content-based ME algorithm [8],[13]. By adopting Full Search (FS) and Three Step Search (TSS) alternatively according to the nature of video contents, this algorithm keeps the visual quality very close to that of FS with only 3% of its computational power. We designed a flexible Block Matching (BM) Unit with 16-PE SIMD data path so that the adaptive ME can be performed at a much lower clock frequency and hardware cost as compared with previous FS based work. To reduce the energy cost caused by excessive external memory access, on-chip SRAM is also utilized and optimized for parallel processing in the BM Unit. The ME engine is fabricated with TSMC 0.18 µm technology. When processing QCIF (15 fps) video, the estimated power is 2.88 mW@4.16 MHz (supply voltage: 1.62 V). It is believed to be a favorable contribution to the video encoder LSI design for mobile applications.

This paper presents a measurement-domain intra prediction coding framework that is compatible with compressive sensing (CS)-based image sensors. In this framework, we propose a low-complexity intra prediction algorithm that can be directly applied to measurements captured by the image sensor. We proposed a structural random 0/1 measurement matrix, embedding the block boundary information that can be extracted from the measurements for intra prediction. Furthermore, a low-cost Very Large Scale Integration (VLSI) architecture is implemented for the proposed framework, by substituting the matrix multiplication with shared adders and shifters. The experimental results show that our proposed framework can compress the measurements and increase coding efficiency, with 34.9% BD-rate reduction compared to the direct output of CS-based sensors. The VLSI architecture of the proposed framework is 9.1 Kin area, and achieves the 83% reduction in size of memory bandwidth and storage for the line buffer. This could significantly reduce both the energy consumption and bandwidth in communication of wireless camera systems, which are expected to be massively deployed in the Internet of Things (IoT) era.

Compressed Sensing based CMOS image sensor (CS-CIS) is a new generation of CMOS image sensor that significantly reduces the power consumption. For CS-CIS, the image quality and data volume of output are two important issues to concern. In this paper, we first proposed an algorithm to generate a series of deterministic and ternary matrices, which improves the image quality, reduces the data volume and are compatible with CS-CIS. Proposed matrices are derived from the approximate DCT and trimmed in 2D-zigzag order, thus preserving the energy compaction property as DCT does. Moreover, we proposed matrix row operations adaptive to the proposed matrix to further compress data (measurements) without any image quality loss. At last, a low-cost VLSI architecture of measurements compression with proposed matrix row operations is implemented. Experiment results show our proposed matrix significantly improve the coding efficiency by BD-PSNR increase of 4.2 dB, comparing with the random binary matrix used in the-state-of-art CS-CIS. The proposed matrix row operations for measurement compression further increases the coding efficiency by 0.24 dB BD-PSNR (4.8% BD-rate reduction). The VLSI architecture is only 4.3 K gates in area and 0.3 mW in power consumption.

Recently, non-binary low-density parity-check (NB-LDPC) codes starts to show their superiority in achieving significant coding gains when moderate codeword lengths are adopted. However, the overwhelming decoding complexity keeps NB-LDPC codes from being widely employed in modern communication devices. This paper proposes a hybrid message-passing decoding algorithm which consumes very low computational complexity. It achieves competitive error performance compared with conventional Min-max algorithm. Simulation result on a (255,174) cyclic code shows that this algorithm obtains at least 0.5dB coding gain over other state-of-the-art low-complexity NB-LDPC decoding algorithms. A partial-parallel NB-LDPC decoder architecture for cyclic NB-LDPC codes is also developed based on this algorithm. Optimization schemes are employed to cut off hard decision symbols in RAMs and also to store only part of the reliability messages. In addition, the variable node units are redesigned especially for the proposed algorithm. Synthesis results demonstrate that about 24.3% gates and 12% memories can be saved over previous works.

In this paper, we propose a power-efficient LDPC decoder architecture based on an accelerated message-passing schedule. The proposed decoder architecture is characterized as follows: (i) Partitioning a pipelined operation not to read and write intermediate messages simultaneously enables the accelerated message-passing schedule to be implemented with single-port SRAMs. (ii) FIFO-based buffering reduces the number of SRAM banks and words of the LDPC decoder based on the accelerated message-passing schedule. The proposed LDPC decoder keeps a single message for each non-zero bit in a parity check matrix as well as a classical schedule while achieving the accelerated message-passing schedule. Implementation results in 0.18 [µm] CMOS technology show that the proposed decoder architecture reduces an area of the LDPC decoder by 43% and a power dissipation by 29% compared to the conventional architecture based on the accelerated message-passing schedule.

One full search variable block size motion estimation (VBSME) architecture with integer pixel accuracy is proposed in this paper. This proposed architecture has following features: (1) Through widening data path from the search area memories, m processing element groups (PEG) could be scheduled to work in parallel and fully utilized, where m is a factor of sixteen. Each PEG has sixteen processing elements (PE) and just costs 8.5K gates. This feature provides users more flexibility to make tradeoff between the hardware cost and the performance. (2) Based on pipelining and multi-cycle data path techniques, this architecture can work at high clock frequency. (3) The memory partition number is greatly reduced. When sixteen PEGs are adopted, only two memory partitions are required for the search area data storage. Therefore, both the system hardware cost and power consumption can be saved. A 16-PEG design with 4832 search range has been implemented with TSMC 0.18 µm CMOS technology. In typical work conditions, its maximum clock frequency is 261 MHz. Compared with the previous 2-D architecture [9], about 13.4% hardware cost and 5.7% power consumption can be saved.

Traffic sign detection is a valuable part of future driver support system. In this paper, we present a novel framework to accurately detect traffic signs from a single color image by analyzing geometrical, physical and text/symbol features of traffic signs. First, we utilize an elaborate edge detection algorithm to extract edge map and accurate edge pixel gradient information. Then, we extract 2-D geometric primitives (circles, ellipses, rectangles and triangles) efficiently from image edge map. Third, the candidate traffic sign regions are selected by analyzing the intrinsic color features, which are invariant to different illumination conditions, of each region circumvented by geometric primitives. Finally, a text and symbol detection algorithm is introduced to classify true traffic signs. Experimental results demonstrated the capabilities of our algorithm to detect traffic signs with respect to different size, shape, color and illumination conditions.

In this paper, we propose two methods to estimate clock jitter caused by power supply noise in a LSI (Large-Scale Integrated circuit). One of the methods enables estimation of clock jitter at the initial design stage before floor-planning. The other method reduces simulation time of clock distribution network to analyze clock jitter at the design verification stage after place-and-route of the chip. For an example design, the relative difference between clock jitter estimated at the initial design stage and that of the design verification stage is 23%. The example result also shows that the proposed method for the verification stage is about 24 times faster than the conventional one to analyze clock jitter.

This paper presents a simple and effective method to further reduce the search points in multilevel successive elimination algorithm (MSEA). Because the calculated sea values of those best matching search points are much smaller than the current minimum SAD, we can simply increase the calculated sea values to increase the elimination ratio without much affecting the coding quality. Compared with the original MSEA algorithm, the proposed strict MSEA algorithm (SMSEA) can provide average 6.52 times speedup. Compared with other lossy fast ME algorithms such as TSS and DS, the proposed SMSEA can maintain more stable image quality. In practice, the proposed technique can also be used in the fine granularity SEA (FGSEA) algorithm and the calculation process is almost the same.

This paper proposes a frequency diversity scheme using only even-numbered samples for single-carrier transmission with frequency-domain equalization (SC-FDE). In the proposed scheme, a periodical frequency spectrum generated by using only even-numbered samples in the time domain provides the frequency redundancy, which is utilized for frequency diversity. Moreover, in order to avoid the data rate reduction due to the decrease in the samples within one block, the high-level modulation is applied to each sample and the transmitting power of each sample can be doubled for the equivalent power transmission instead. Computer simulation results show that the proposed scheme provides a steeper BER curve than the typical SC-FDE over frequency selective fading channels, while the typical SC-FDE is more favorable than the proposed scheme over flat fading channels. Moreover, the proposed scheme still retains its characteristic even when channel estimation and channel coding are additionally taken into account.